Easily deposited ZnO nanorods on siloxene nanosheets: investigation of morphological, dielectric, ferroelectric, and energy storage properties.

The integration of metal oxides onto two-dimensional layered siloxene has proven to be an effective strategy for expanding potential applications across diverse fields. Herein, we present the synthesis and detailed characterization of zinc oxide (ZnO) nanorods deposited on siloxene nanosheets using the wet chemical precipitation method without the need of alkali. The presence of ZnO nanorods was confirmed through electron microscopy analyses. X-ray diffraction analysis further verified the presence of characteristic peaks of ZnO in the hexagonal wurtzite crystal structure. Dielectric measurements demonstrated the moderated stability of interfacial polarization in siloxene nanosheets doped with zinc oxide (SX-ZnO) over a broad frequency spectrum, coupled with minimal electrical loss values under 0.4 within the 100 Hz to 1 MHz frequency range. In addition, the ferroelectric study of SiNSs-ZnO composites revealed a slim hysteresis loop with maximum polarization and remnant polarization values that varied with reaction times. The SX-ZnO sample prepared for 5 h exhibited the best stored energy properties, featuring a moderate stored energy density (Ws = 771.94 mJ cm-3) and a high energy efficiency of 83.38%. This investigation underscores that the modification of siloxene layers through the deposition of nanostructured transition metal oxide materials leads to stabilized interfacial polarization and enhanced efficient energy storage.

Ionothermal Carbonization of Sugarcane Bagasse in 1-Alkyl-3-methylimidazolium Ionic Liquids: Insights into the Role of the Chloroferrate Anion.

We report the ionothermal carbonization (ITC) of lignocellulosic biomass in imidazolium tetrachloroferrate ionic liquids (ILs) as an advantageous approach for the preparation of nanostructured carbonaceous materials, namely, ionochars. In a previous study, we investigated the role of the imidazolium cation and demonstrated the possibility of controlling both the textural and morphological properties of ionochars by cation engineering. Although essential for providing intermediate Lewis acidity and relatively high thermal stability, the role of the chloroferrate anion is still open to debate. Herein, we investigated the ITC of sugarcane bagasse and its main component, cellulose, in 1-alkyl-3-methylimidazolium ILs with different chloroferrate anions. We identified anionic speciation and its impact on the properties of the IL by Raman spectroscopy, thermogravimetric analysis, and differential scanning calorimetry. The obtained ionochars were characterized by gas physisorption, electron microscopy, Raman spectroscopy, Fourier transform infrared (FTIR) spectroscopy, and 13C solid-state CP-MAS NMR spectroscopy. We show that the anionic species have a predominant impact on the textural and morphological properties of the ionochars.

Design, synthesis, and molecular modeling studies of novel 2-quinolone-1,2,3-triazole-α-aminophosphonates hybrids as dual antiviral and antibacterial agents.

With the aim to identify new antiviral agents with antibacterial properties, a series of 2-quinolone-1,2,3-triazole derivatives bearing α-aminophosphonates was synthesized and characterized by 1H NMR, 13C NMR, 31P NMR, single crystal XRD and HRMS analyses. These compounds were examined against five RNA viruses (YFV, ZIKV, CHIKV, EV71 and HRV) from three distinct families (Picornaviridae, Togaviridae and Flaviviridae) and four bacterial strains (S. aureus, E. feacalis, E. coli and P. aeruginosa). The α-aminophosphonates 4f, 4i, 4j, 4k, 4p and 4q recorded low IC50 values of 6.8-10.91 µM, along with elevated selectivity indices ranging from 2 to more than 3, particularly against YFV, CHIKV and HRV-B14. Besides, the synthesized compounds were generally more sensitive toward Gram-positive bacteria, with the majority of them displaying significant potency against E. feacalis. Specifically, an excellent anti-enterococcus activity was obtained by compound 4q with MIC and MBC values of 0.03 µmol/mL, which were 8.7 and 10 times greater than those of the reference drugs ampicillin and rifampicin, respectively. Also, compounds 4f, 4p and 4q showed potent anti-staphylococcal activity with MIC values varying between 0.11 and 0.13 µmol/mL, compared to 0.27 µmol/mL for ampicillin. The results from DFT and molecular docking simulations were in agreement with the biological assays, proving the binding capability of hybrids 4f, 4i, 4j, 4k, 4p and 4q with viral and bacterial target enzymes through hydrogen bonds and other non-covalent interactions. The in silico ADME/Tox prediction revealed that these molecules possess moderate to good drug-likeness and pharmacokinetic properties, with a minimal chance of causing liver toxicity or carcinogenic effects.

Selective Functionalization of Carbonyl Closo-Decaborate [2-B10H9CO]- with Building Block Properties via Grignard Reagents.

A green, fast and selective approach for the synthesis of mono-substituted closo-decaborate derivatives [2-B10H9COR]2- has been established via a nucleophilic addition reaction between the carbonyl derivative of closo-decaborate [2-B10H9CO]- and the corresponding Grignard reagent RMgX, where R is the ethyl, iso-propyl, pentyl, allyl, vinyl and propynyl groups. This approach is accomplished under mild conditions with 70-80% yields. The significance of these derivative is their ability to constitute building blocks for polymeric integration via the allyl, vinyl and propynyl substituents. All products were characterized by 11B, 1H and 13C NMR, elemental analysis and mass spectrometry.

Photocatalytic degradation of chloroform using rGO-CuS nanocomposite under UV/VIS irradiation from gaseous phase.

Environmental pollutants such as organic solvents pose potential hazards to the environment. One of the most commonly used solvents, chloroform, is known to cause heart attacks, respiratory problems, and central nervous system disorders. At the pilot scale, the efficacy of the photocatalytic process for removing chloroform from gas streams using the rGO-CuS nanocomposite was investigated. The results indicated that chloroform degradation at 1.5 L min*1 (74.6%) was more than twice as fast as at 2.0 L min-1 (30%). With increasing relative humidity, the chloroform removal efficiency increased up to 30% and then declined. Therefore, 30% humidity was found to be the optimal humidity for the photocatalyst. As the rGO-CuS ratio increased, the photocatalytic degradation efficiency decreased, and the chloroform oxidation rate increased at higher temperatures. The process efficiency increases with increasing pollutant concentrations until the vacant sites are saturated. After the saturation of these active sites, process efficiency does not change.

[Which anticoagulant or antiplatelet treatment for cancer patients with thrombocytopenia ?] / Quel anticoagulant ou antiagrégant chez le patient oncologique présentant une thrombocytopénie ?

Cancer patients have an increased thrombotic risk of arterial and venous thrombosis. Thrombocytopenia, particularly with anticoagulation, exposes the patient to an increased risk of bleeding but does not reduce the risk of recurrent thrombosis. When platelets are < 50 × 109/l, the strategy regarding anticoagulation must be reassessed. Based on the thrombotic and bleeding risks as well as the expected duration of thrombocytopenia, management options include full-dose treatment with platelet transfusion, reduced-dose anticoagulation or withholding antithrombotic therapy. Aspirin treatment appears to be a reasonable choice for thrombocytopenic (> 30 × 109/l) patients with acute coronary syndrome. This paper will review the guidelines on anticoagulation and antiplatelet therapy in thrombocytopenic cancer patients.

Les patients avec un cancer ont un risque thrombotique artériel et veineux accru. En cas de thrombocytopénie et traitement anticoagulant (ou antiagrégant), ils sont exposés à un risque hémorragique augmenté mais conservent un risque thrombotique élevé. L'évaluation de l'anticoagulation s'impose pour des thrombocytes < 50 × 109/l. En fonction des risques thrombotique et hémorragique et de la durée de la thrombocytopénie, les options sont la poursuite de l'anticoagulation, le recours aux transfusions plaquettaires, la réduction de la dose ou son interruption. Un traitement par aspirine en cas de syndrome coronarien aigu est raisonnable pour des thrombocytes > 30 × 109/l. Cet article propose une revue des recommandations concernant les traitements anticoagulants ou antiagrégants en cas de thrombocytopénie chez les patients oncologiques.

Gelatin modified with alkoxysilanes (GelmSi) forms hybrid hydrogels for bioengineering applications.

Biopolymers are ideal candidates for the development of hydrogels for tissue engineering applications. However, chemical modifications are required to further improve their mechanical properties, in particular to cross-link them for long-lasting applications or biofabrication. Herein, we developed a novel gelatin-based hydrogel precursor, "GelmSi" which consist on modified gelatin with triethoxysilyl groups. Gelatin was chosen as starting material because of its biocompatibility and bioactivity, favouring cell adhesion and migration. Alkoxysilane moieties were introduced in a controlled manner on the lysine side chains of gelatin to obtain a hybrid precursor which reacts in physiological conditions, forming covalent siloxane bonds and allowing the formation of a three-dimensional chemical network. On the contrary to unmodified gelatin, siloxane covalent network dramatically increases the stiffness and the thermal stability of the resulting gelatin-based hydrogel, making it suitable for cell encapsulation and cell culture. The biorthogonality and versatility of the GelmSi hybrid hydrogel unlock a broad range of gelatin-based bioengineering applications.

Long-term stable solid concentrated graphene dispersion assisted by a highly aromatic ionic liquid.

HYPOTHESIS: The sonochemical exfoliation of graphite in solution has been demonstrated as a promising and easy technique for producing graphene dispersions. This is usually done in organic solvents and leads to unstable dispersions with very low graphene concentration. Ionic liquids (ILs) represent a versatile and safe alternative to traditional organic solvents. A few recent studies reported the use of commercial ILs with bulky anions, such as bis(trifluoromethylsulfonyl)imide, and aromatic cations, such as imidazolium, which favour the exfoliation of graphite through π-π and cation-π interactions. Although recently investigated, the role of aromatic groups on imidazolium cations is still controversial and systematic studies are still necessary. Besides, these studies were limited to liquid dispersions at room temperature. EXPERIMENTS: Herein, we prepared four highly aromatic imidazolium-based ILs, including the newly reported 1-(naphthylmethyl)-3-benzylimidazolium bis(trifluoromethanesulfonyl)imide, [(Np)(Bn)im][NTf2]. These ILs were used for the sonochemical exfoliation of graphite and compared with a commercial benchmark, 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide [Bmim][NTf2]. FINDINGS: Interestingly, [(Np)(Bn)im][NTf2] allowed reaching solid dispersions at room temperature containing thin few layer graphene sheets with long-term stability (up to 2 years) and high concentration (3.6 mg/mL). Such graphene dispersion combines long-term stability in the solid-state and high processability in the liquid state, by a simple heating above 60 °C.

Synthesis of new 3-acetyl-1,3,4-oxadiazolines combined with pyrimidines as antileishmanial and antiviral agents.

A new series of 3-acetyl-1,3,4-oxadiazoline hybrid molecules was designed and synthesized using a condensation between acyclonucleosides and substituted phenylhydrazone. All intermediates and final products were screened against Leishmania donovani, a Protozoan parasite and against three viruses SARS-CoV-2, HCMV and VZV. While no significant activity was observed against the viruses, the intermediate with 6-azatymine as thymine and 5-azathymine-3-acetyl-1,3,4-oxadiazoline hybrid exhibited a significant antileishmanial activity. The later compound was the most promising, exhibiting an IC50 value at 8.98 µM on L. donovani intramacrophage amastigotes and a moderate selectivity index value at 2.4.

Silylated biomolecules: Versatile components for bioinks.

Physical hydrogels prepared from natural biopolymers are the most popular components for bioinks. However, to improve the mechanical properties of the network, in particular its durability for long-lasting tissue engineering applications or its stiffness for bone/cartilage applications, covalent chemical hydrogels have to be considered. For that purpose, biorthogonal reactions are required to allow the inclusion of living cells within the bioink reservoir before the 3D printing procedure. Interestingly, such reactions also unlock the possibility to further multifunctionalize the network, adding bioactive moieties to tune the biological properties of the resulting printed biomaterial. Surprisingly, compared to the huge number of studies disclosing novel bioink compositions, no extensive efforts have been made by the scientific community to develop new chemical reactions meeting the requirements of both cell encapsulation, chemical orthogonality and versatile enough to be applied to a wide range of molecular components, including fragile biomolecules. That could be explained by the domination of acrylate photocrosslinking in the bioprinting field. On the other hand, proceeding chemoselectively and allowing the polymerization of any type of silylated molecules, the sol-gel inorganic polymerization was used as a crosslinking reaction to prepare hydrogels. Recent development of this strategy includes the optimization of biocompatible catalytic conditions and the silylation of highly attractive biomolecules such as amino acids, bioactive peptides, proteins and oligosaccharides. When one combines the simplicity and the versatility of the process, with the ease of functionalization of any type of relevant silylated molecules that can be combined in an infinite manner, it was obvious that a family of bioinks could emerge quickly. This review presents the sol-gel process in biocompatible conditions and the various classes of relevant silylated molecules that can be used as bioink components. The preparation of hydrogels and the kinetic considerations of the sol-gel chemistry which at least allowed cell encapsulation and extrusion-based bioprinting are discussed.

Textural control of ionosilicas by ionic liquid templating.

Due to their unique self-assembly properties, ionic liquids (ILs) are versatile soft templates for the formation of mesoporous materials. Here, we report the use of ionic liquids as soft templates for the straightforward formation of mesoporous ionosilica phases. Ionosilicas are highly polyvalent functional materials that are constituted of ionic building blocks that are covalently immobilized within a silica hybrid matrix. Ionosilicas have attracted significant interest in the last few years due to their high potential for applications in water treatment and upgrading, separation and drug delivery. The straightforward and reproducible formation of mesoporous ionosilica phases is therefore highly desirable. In this context, we report the formation of mesoporous ionosilica phases via non-hydrolytic sol-gel procedures in the presence of ionic liquids. Ionic liquids appear as particularly versatile templates for mesoporous ionosilicas due to their high chemical similarity and affinity between ILs and silylated ionic precursors. We therefore studied the textures of the resulting ionosilica phases, after IL elimination, using nitrogen sorption, small angle X-ray scattering (SAXS) and transmission and scanning electron microscopies. All these techniques give concordant results and show that the textures of ionosilica scaffolds in terms of specific surface area, pore size, pore size distribution and connectivity can be efficiently controlled by the nature and the quantity of the ionic liquid that is used in the ionothermal sol-gel procedure.

Hydrolytic vs. Nonhydrolytic Sol-Gel in Preparation of Mixed Oxide Silica-Alumina Catalysts for Esterification.

The development of green and sustainable materials for use as heterogeneous catalysts is a growing area of research in chemistry. In this paper, mesoporous SiO2-Al2O3 mixed oxide catalysts with different Si/Al ratios were prepared via hydrolytic (HSG) and nonhydrolytic sol-gel (NHSG) processes. The HSG route was explored in acidic and basic media, while NHSG was investigated in the presence of diisopropylether as an oxygen donor. The obtained materials were characterized using EDX, N2-physisorption, powder XRD, 29Si, 27Al MAS-NMR, and NH3-TPD. This approach offered good control of composition and the Si/Al ratio was found to influence both the texture and the acidity of the mesoporous materials. According to 27Al and 29Si MAS NMR analyses, silicon and aluminum were more regularly distributed in NHSG samples that were also more acidic. Silica-alumina catalysts prepared via NHSG were more active in esterification of acetic acid with n-BuOH.

Key signaling networks are dysregulated in patients with the adipose tissue disorder, lipedema.

OBJECTIVES: Lipedema, a poorly understood chronic disease of adipose hyper-deposition, is often mistaken for obesity and causes significant impairment to mobility and quality-of-life. To identify molecular mechanisms underpinning lipedema, we employed comprehensive omics-based comparative analyses of whole tissue, adipocyte precursors (adipose-derived stem cells (ADSCs)), and adipocytes from patients with or without lipedema. METHODS: We compared whole-tissues, ADSCs, and adipocytes from body mass index-matched lipedema (n = 14) and unaffected (n = 10) patients using comprehensive global lipidomic and metabolomic analyses, transcriptional profiling, and functional assays. RESULTS: Transcriptional profiling revealed >4400 significant differences in lipedema tissue, with altered levels of mRNAs involved in critical signaling and cell function-regulating pathways (e.g., lipid metabolism and cell-cycle/proliferation). Functional assays showed accelerated ADSC proliferation and differentiation in lipedema. Profiling lipedema adipocytes revealed >900 changes in lipid composition and >600 differentially altered metabolites. Transcriptional profiling of lipedema ADSCs and non-lipedema ADSCs revealed significant differential expression of >3400 genes including some involved in extracellular matrix and cell-cycle/proliferation signaling pathways. One upregulated gene in lipedema ADSCs, Bub1, encodes a cell-cycle regulator, central to the kinetochore complex, which regulates several histone proteins involved in cell proliferation. Downstream signaling analysis of lipedema ADSCs demonstrated enhanced activation of histone H2A, a key cell proliferation driver and Bub1 target. Critically, hyperproliferation exhibited by lipedema ADSCs was inhibited by the small molecule Bub1 inhibitor 2OH-BNPP1 and by CRISPR/Cas9-mediated Bub1 gene depletion. CONCLUSION: We found significant differences in gene expression, and lipid and metabolite profiles, in tissue, ADSCs, and adipocytes from lipedema patients compared to non-affected controls. Functional assays demonstrated that dysregulated Bub1 signaling drives increased proliferation of lipedema ADSCs, suggesting a potential mechanism for enhanced adipogenesis in lipedema. Importantly, our characterization of signaling networks driving lipedema identifies potential molecular targets, including Bub1, for novel lipedema therapeutics.

Development of Amino Acids Functionalized SBA-15 for the Improvement of Protein Adsorption.

Ordered mesoporous materials and their modification with multiple functional groups are of wide scientific interest for many applications involving interaction with biological systems and biomolecules (e.g., catalysis, separation, sensor design, nano-science or drug delivery). In particular, the immobilization of enzymes onto solid supports is highly attractive for industry and synthetic chemistry, as it allows the development of stable and cheap biocatalysts. In this context, we developed novel silylated amino acid derivatives (Si-AA-NH2) that have been immobilized onto SBA-15 materials in biocompatible conditions avoiding the use of toxic catalyst, solvents or reagents. The resulting amino acid-functionalized materials (SBA-15@AA) were characterized by XRD, TGA, EA, Zeta potential, nitrogen sorption and FT-IR. Differences of the physical properties (e.g., charges) were observed while the structural ones remained unchanged. The adsorption of the enzyme lysozyme (Lyz) onto the resulting functionalized SBA-15@AA materials was evaluated at different pHs. The presence of different functional groups compared with bare SBA-15 showed better adsorption results, for example, 79.6 nmol of Lyz adsorbed per m2 of SBA-15@Tyr compared with the 44.9 nmol/m2 of the bare SBA-15.

A Collagen-Mimetic Organic-Inorganic Hydrogel for Cartilage Engineering.

Promising strategies for cartilage regeneration rely on the encapsulation of mesenchymal stromal cells (MSCs) in a hydrogel followed by an injection into the injured joint. Preclinical and clinical data using MSCs embedded in a collagen gel have demonstrated improvements in patients with focal lesions and osteoarthritis. However, an improvement is often observed in the short or medium term due to the loss of the chondrocyte capacity to produce the correct extracellular matrix and to respond to mechanical stimulation. Developing novel biomimetic materials with better chondroconductive and mechanical properties is still a challenge for cartilage engineering. Herein, we have designed a biomimetic chemical hydrogel based on silylated collagen-mimetic synthetic peptides having the ability to encapsulate MSCs using a biorthogonal sol-gel cross-linking reaction. By tuning the hydrogel composition using both mono- and bi-functional peptides, we succeeded in improving its mechanical properties, yielding a more elastic scaffold and achieving the survival of embedded MSCs for 21 days as well as the up-regulation of chondrocyte markers. This biomimetic long-standing hybrid hydrogel is of interest as a synthetic and modular scaffold for cartilage tissue engineering.

The Effect of Size and Thermal Treatment on the Photoluminescent Properties of Europium-Doped SiO2 Nanoparticles Prepared in One Pot by Sol-Gel.

Europium (Eu)-doped silica nanoparticles have attracted great interest for different applications, in particular in biomedicine as biosensors or for tissue regeneration. Sol-gel is the most common process used to prepare those particles, with size varying from tens to hundreds of nanometers. In this article, we focus our attention on the comparison between two commonly used sol-gel derived methods: reverse microemulsion (for particles smaller than 100 nm) and Stöber method (for particles larger than 100 nm). Europium concentration was varied between 0.2 and 1 mol%, and the nanoparticle diameters were 10, 50 and 100 nm. The link between the local environment of europium ions and their optical properties was investigated and discussed. Using Transmission Electron Microscopy, nitrogen sorption, X-ray diffraction, Fourier-Transform Infra-Red and pulsed doubled Nd:YAG laser, we confirmed that fluorescence lifetime was improved by thermal treatment at 900 °C due to the elimination of aqueous environment and modification of structure disorder. The size of nanoparticles, the amount of europium and the thermal treatment of obtained materials influence the emission spectra and the decay curves of Eu3+.

Sol-gel process: the inorganic approach in protein imprinting.

Proteins play a central role in the signal transmission in living systems since they are able to recognize specific biomolecules acting as cellular receptors, antibodies or enzymes, being themselves recognized by other proteins in protein/protein interactions, or displaying epitopes suitable for antibody binding. In this context, the specific recognition of a given protein unlocks a range of interesting applications in diagnosis and in targeted therapies. Obviously, this role is already fulfilled by antibodies with unquestionable success. However, the design of synthetic artificial systems able to endorse this role is still challenging with a special interest to overcome limitations of antibodies, in particular their production and their stability. Molecular Imprinted Polymers (MIPs) are attractive recognition systems which could be an alternative for the specific capture of proteins in complex biological fluids. MIPs can be considered as biomimetic receptors or antibody mimics displaying artificial paratopes. However, MIPs of proteins remains a challenge due to their large size and conformational flexibility, their complex chemical nature with multiple recognition sites and their low solubility in most organic solvents. Classical MIP synthesis conditions result in large polymeric cavities and unspecific binding sites on the surface. In this review, the potential of the sol-gel process as inorganic polymerization strategy to overcome the drawbacks of protein imprinting is highlighted. Thanks to the mild and biocompatible experimental conditions required and the use of water as a solvent, the inorganic polymerization approach better suited to proteins than organic polymerization. Through numerous examples and applications of MIPs, we proposed a critical evaluation of the parameters that must be carefully controlled to achieve sol-gel protein imprinting (SGPI), including the choice of the monomers taking part in the polymerization.

When graphene meets ionic liquids: a good match for the design of functional materials.

Graphene is an attractive material that is characterized by its exceptional properties (i.e. electrical, mechanical, thermal, optical, etc.), which have pushed researchers to attach high interest to its production and functionalization processes to meet applications in different fields (electronics, electromagnetics, composites, sensors, energy storage, etc.). The synthesis (bottom-up) of graphene remains long and laborious, at the same time expensive, and it is limited to the development of this material in low yield. Hence, the use of graphite as a starting material (top-down through exfoliation or oxidation) seems a promising and easy technique for producing a large quantity of graphene or graphene oxide (GO). On the one hand, GO has been extensively studied due to its ease of synthesis, processing and chemical post-functionalization. One the other hand, "pristine" graphene sheets, obtained through exfoliation, are limited in processability but present enhanced electronic properties. Both types of materials have been of great interest to design functional nanomaterials. Ionic liquids (ILs) are task-specific solvents that exhibit tunable physico-chemical properties. ILs have many advantages as compared with conventional solvents, such as high thermal and chemical stability, low volatility, excellent conductivity and inherent polarity. In the last decade, ILs have been widely employed for the preparation and stabilization of various nanomaterials. In particular, the combination of ILs and graphene, including GO and pristine graphene sheets, has been of growing interest for the preparation, processing and functionalization of hybrid nanomaterials. Understanding the structure and properties of the graphene/IL interface has been of considerable interest for a large panel of applications ranging from tribology to energy storage.

Design of PEGylated Three Ligands Silica Nanoparticles for Multi-Receptor Targeting.

The synthesis of silica nanoparticles (SiNPs) decorated on their surface with a range of various elements (e.g., ligands, drugs, fluorophores, vectors, etc.) in a controlled ratio remains a big challenge. We have previously developed an efficient strategy to obtain in one-step, well-defined multifunctional fluorescent SiNPs displaying fluorophores and two peptides ligands as targeting elements, allowing selective detection of cancer cells. In this paper, we demonstrate that additional level of controlled multifunctionality can be achieved, getting even closer to the original concept of "magic bullet", using solely sol-gel chemistry to achieve conjugation of PEG chains for stealth, along with three different ligands. In addition, we have answered the recurrent question of the surface ungrafting by investigating the stability of different siloxane linkages with the ERETIC Method (Electronic Reference to Access In Vivo Concentrations) by 19F NMR quantification. We also compared the efficiency of the hybrid silylated fluorophore covalent linkage in the core of the SiNP to conventional methods. Finally, the tumor-cell-targeting efficiency of these multi-ligand NPs on human endothelial cells (HUVEC or HDMEC) and mixed spheroids of human melanoma cells and HUVEC displaying different types of receptors were evaluated in vitro.

Design, synthesis, biological evaluation and molecular docking of new 1,3,4-oxadiazole homonucleosides and their double-headed analogs as antitumor agents.

A novel series of homonucleosides and their double-headed analogs containing theophylline, 1,3,4-oxadiazole, and variant nucleobases was designed and synthesized. The new derivatives were fully characterized by HRMS, FT-IR, 1H NMR, and 13C NMR. The cytotoxic activities of all prepared compounds were screened in vitro against four cell lines, including fibrosarcoma (HT-1080), breast (MCF-7 and MDA-MB-231), and lung carcinoma (A-549). The double-headed analogue 18 showed marked growth inhibition against all the cell lines tested, specifically in HT-1080, with an IC50 values of 17.08 ± 0.97 µM. The possible mechanism of apoptosis was investigated using Annexin V staining, caspase-3/7 activity, and analysis cell cycle progression. The compound 18 induced apoptosis through caspase-3/7 activation and cell-cycle arrest in HT-1080 and A-549 cells. The molecular docking confirms that the compound 18 activated caspase-3 via the formation of hydrogen bonds and hydrophobic interactions.